Service range
Standard Material | |||
Material codes | Pressure MPa {kgf/㎠} | Max. speed (m/s) |
Temperature
range (℃) |
NBR(RN819) FKM[RF903] |
- | 1 | ー25~100 [ー5~150] |
Material codes・The range with [ ] refers FKM materials
Characteristics
Dust seals with rubber coated metal rim placed on the outer circuit.
Protecting packings and cylinders bypreventing the penetration of dust from the outside.
It is specially designed for the prevention of penetrating fluids.
Protecting packings and cylinders bypreventing the penetration of dust from the outside.
It is specially designed for the prevention of penetrating fluids.
Remarks
- ●Wipers should be installed in the direction specified in the above schematic.
- ●For the way of installation, check Installation Method.
- ●Refer to the ℓ dimension as it would be differed according to the type of packings to be used together.
- ●As pressure plate flat system requires the inner dimension of pressure bar different from that of SCB-wiper, refer to the table below.
- ●For ℓ(L) dimensions when using the dust seal alone, please refer to the SKY dimensions.
- ※JIS standard sequence of surface roughness symbols refer to HERE.
Dimension table
Dimension table
- 1) For dust-proof application, choose the suitable one out of the standard wipers.
- 2) SDB-wipers have strong wiping ability of oil film on the surface of the rod. Note that the use of them as standard wipers for hydraulic and pneumatic cylinders may wipe out lubricants and grease inside.
- 3) Do not apply any lubricants such as grease to the outer ring surface of wipers and the inside of the housing to avoid floating of wipers from the housing at installation. (no problem in the use for press fit installation)
- 4) At the insertion of the rod, apply grease to the inner ring of wipers and the rod surface to avoid damages on the lip part.
Part No. | GA | a |
---|---|---|
8~16 | 5.5 | 0.25 |
18~30 | 6.5 | |
32~50 | 8.0 | |
56 | 9.0 | 0.35 |
Wipers & Groove dimensions(Unit:mm) | Part No. | Compatible SCB-wipers | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
d | D | H | h | G | B | D1 | D2 | m | C | Standard (RN819) |
Material for chlorine fluid (RF 903) |
Retaining ring | ||
8 | 18 | 7.5 | 4.8 | 5 | 3.5 | 18.8±0.1 | 17.8 | 0.7 | 14.9 | 2 | SDB-8 | SDB-8F | DSP-8 | SCB-8 |
10 | 20 | 7.5 | 4.8 | 5 | 3.5 | 21 ±0.1 | 19.8 | 0.7 | 16.9 | 2 | SDB-10 | SDB-10F | DSP-10 | SCB-10 |
12 | 22 | 7.5 | 4.8 | 5 | 3.5 | 23 ±0.1 | 21.8 | 0.7 | 18.9 | 2 | SDB-12 | SDB-12F | DSP-12 | SCB-12-1* |
14 | 24 | 7.5 | 4.8 | 5 | 3.5 | 25 ±0.1 | 23.8 | 0.7 | 20.9 | 2 | SDB-14 | SDB-14F | DSP-14 | SCB-14 |
16 | 26 | 7.5 | 4.8 | 5 | 3.5 | 27 ±0.1 | 25.8 | 0.7 | 22.9 | 2 | SDB-16 | SDB-16F | DSP-16 | SCB-16 |
18 | 30 | 9 | 5.8 | 6 | 4.5 | 31.5±0.1 | 29.8 | 0.8 | 26.3 | 2 | SDB-18 | SDB-18F | DSP-18 | SCB-18 |
20 | 32 | 9 | 5.8 | 6 | 4.5 | 33.5±0.1 | 31.8 | 0.8 | 28.3 | 2 | SDB-20 | SDB-20F | DSP-20 | SCB-20 |
22.4 | 34.4 | 9 | 5.8 | 6 | 4.5 | 35.9±0.1 | 34.2 | 0.8 | 30.7 | 2 | SDB-22.4 | SDB-22.4F | DSP-22.4 | SCB-22.4 |
25 | 37 | 9 | 5.8 | 6 | 4.5 | 38.5±0.1 | 36.8 | 0.8 | 33.3 | 2 | SDB-25 | SDB-25F | DSP-25 | SCB-25 |
28 | 40 | 9 | 5.8 | 6 | 4.5 | 41.5±0.1 | 39.8 | 0.8 | 36.3 | 2 | SDB-28 | SDB-28F | DSP-28 | SCB-28 |
30 | 42 | 9 | 5.8 | 6 | 4.5 | 43.5±0.1 | 41.8 | 0.8 | 38.3 | 2 | SDB-30 | SDB-30F | DSP-30 | SCB-30 |
32 | 44 | 10 | 6.8 | 7 | 4.5 | 45.5±0.1 | 43.8 | 0.8 | 40.3 | 3 | SDB-32 | SDB-32F | DSP-32 | SCB-32 |
35.5 | 47.5 | 10 | 6.8 | 7 | 4.5 | 49.5±0.15 | 47.3 | 1.0 | 43.8 | 3 | SDB-35.5 | SDB-35.5F | DSP-35.5 | SCB-35.5 |
40 | 52 | 10 | 6.8 | 7 | 4.5 | 54 ±0.15 | 51.8 | 1.0 | 48.3 | 3 | SDB-40 | SDB-40F | DSP-40 | SCB-40 |
45 | 57 | 10 | 6.8 | 7 | 4.5 | 59 ±0.15 | 56.8 | 1.0 | 53.3 | 3 | SDB-45 | SDB-45F | DSP-45 | SCB-45 |
50 | 62 | 10 | 6.8 | 7 | 4.5 | 64 ±0.15 | 61.8 | 1.0 | 58.3 | 3 | SDB-50 | SDB-50F | DSP-50 | SCB-50 |
56 | 70 | 11 | 7.7 | 8 | 5 | 72.5±0.15 | 69.6 | 1.1 | 65.5 | 3 | SDB-56 | SDB-56F | DSP-56 | SCB-56 |
- ★Orders and inquiries are acceptable by part numbers. Part numbers marked ※ have been changed each part numbers. Please check HERE for the previous part number.
- ★Part numbers in blue letters are the products in stock.
- ★Wipers with the part numbers in light Italic require the confirmation of their availability prior to ordering. These items are subject to the abolishment without notice. Reclamation of an abolished product requires producing the new tooling at your expense.
- ★Please note that other retaining rings, such as C-shaped retaining rings are not acceptable for the application.
- ★Wipers are adequately packaged for the optimum storage. Refer to Cautions for the handling and storage.
- ★Please check SCB-Wipers, the compatible wipers, of their availability.
- ★Performance and material tests on packing and seals are also available. Please contact us for more information.