Service range
Standard material | |||
Material codes | Pressure MPa {kgf/㎠} | Max. speed (m/s) |
Temperature
range (℃) |
NBR(RN814) | - | 1 | ー45~100 |
Characteristics
Insertable dust seals with large profile for both outdoor and indoor applications.
Protecting packings and cylinders bypreventing the penetration of dust from the outside.
They are specially designed not to penetrate water from the outer circuit of the groove.
Protecting packings and cylinders bypreventing the penetration of dust from the outside.
They are specially designed not to penetrate water from the outer circuit of the groove.
Remarks
- ●Wipers should be installed in the direction specified in the above schematic.
- ●Consider adopting divided grooves if one-piece groove is technically adverse.
- ●Apply enough grease (specified at Materials) to the inside of the groove at the installation. Besides, consider a rust control treatment on the surface ofφC dimension.
- ●Refer to the ℓ dimension as it would be differed according to the type of packings to be used together.
- ●For ℓ(L) dimensions when using the dust seal alone, please refer to the SKY dimensions.
- ※JIS standard sequence of surface roughness symbols refer to HERE.
Dimension table
Wipers & Groove dimensions(Unit:mm) | Part No. | ||||||
---|---|---|---|---|---|---|---|
d | D | H | h | C | G | B | Standard(RN 814) |
18 | 30 | 7.7 | 5.8 | 24 | 6 | 3 | SCK-18 |
20 | 32 | 7.7 | 5.8 | 26 | 6 | 3 | SCK-20 |
25 | 37 | 7.7 | 5.8 | 31 | 6 | 3 | SCK-25 |
28 | 40 | 7.7 | 5.8 | 34 | 6 | 3 | SCK-28 |
30 | 42 | 7.7 | 5.8 | 36 | 6 | 3 | SCK-30 |
32 | 44 | 8.7 | 6.8 | 38 | 7 | 3 | SCK-32 |
35 | 47 | 8.7 | 6.8 | 41 | 7 | 3 | SCK-35 |
40 | 52 | 8.7 | 6.8 | 46 | 7 | 3 | SCK-40 |
45 | 57 | 8.7 | 6.8 | 51 | 7 | 3 | SCK-45 |
50 | 62 | 8.7 | 6.8 | 56 | 7 | 3 | SCK-50 |
55 | 69 | 10 | 7.7 | 62 | 8 | 3 | SCK-55 |
60 | 74 | 10 | 7.7 | 67 | 8 | 3 | SCK-60 |
65 | 79 | 10 | 7.7 | 72 | 8 | 3 | SCK-65 |
70 | 84 | 10 | 7.7 | 77 | 8 | 3 | SCK-70 |
75 | 89 | 10 | 7.7 | 82 | 8 | 3 | SCK-75 |
80 | 94 | 10 | 7.7 | 87 | 8 | 3 | SCK-80 |
85 | 99 | 10 | 7.7 | 92 | 8 | 3 | SCK-85 |
90 | 104 | 10 | 7.7 | 97 | 8 | 3 | SCK-90 |
95 | 109 | 10 | 7.7 | 102 | 8 | 3 | SCK-95 |
100 | 114 | 10 | 7.7 | 107 | 8 | 3 | SCK-100 |
105 | 121 | 12 | 8.7 | 113 | 9 | 4 | SCK-105 |
110 | 126 | 12 | 8.7 | 118 | 9 | 4 | SCK-110 |
115 | 131 | 12 | 8.7 | 123 | 9 | 4 | SCK-115 |
120 | 136 | 12 | 8.7 | 128 | 9 | 4 | SCK-120 |
125 | 141 | 12 | 8.7 | 133 | 9 | 4 | SCK-125 |
130 | 146 | 12 | 8.7 | 138 | 9 | 4 | SCK-130 |
132 | 148 | 12 | 8.7 | 140 | 9 | 4 | SCK-132 |
140 | 160 | 14 | 9.7 | 150 | 10 | 5 | SCK-140 |
160 | 180 | 14 | 9.7 | 170 | 10 | 5 | SCK-160 |
- ★Orders and inquiries are acceptable by part numbers. Part numbers marked ※ have been changed each part numbers. Please check HERE for the previous part number.
- ★Part numbers in blue letters are the products in stock.
- ★Wipers with the part numbers in light Italic require the confirmation of their availability prior to ordering.
These items are subject to the abolishment without notice. Reclamation of an abolished product requires producing the new tooling at your expense. - ★Wipers are adequately packaged for the optimum storage. Refer to Cautions for the handling and storage.
- ★Performance and material tests on packing and seals are also available. Please contact us for more information.